How To Start A Stihl MS 180 C-BE chainsaw And Quick Tips To Improve Cutting

The Stihl MS 180 C-BE is a modern chain saw which has been designed to create fast and powerful cuts. If you have just started using it, you may have found that it is a difficult machine to learn. In this article, I will try to help you get started with your Stihl MS180C BE chainsaw and provide you with some quick tips on how to improve cutting.

Basics Of Starting A Stihl MS 180 C-BE

Stihl MS 180 C-BE

Click Here To See MS180 C-BE Details

Starting the Stihl MS 180 C-BE chainsaw can be intimidating, especially if you’ve never done it before. But don’t worry — it’s easier than you might think. And once you understand how to start a chainsaw, you’ll be able to do it quickly and safely.

  1. Press down on the choke lever at the top of the engine cover. This lever should be in the “up” position when cutting wood, but it’s used to start the engine cold.
  2. Press down on the throttle lockout lever with your thumb while squeezing the throttle trigger towards the handle. The throttle lockout lever is located on top of the handle, next to your left hand when holding the chainsaw. Hold both levers down while you start the saw.
  3. Pull up on the starter rope with your right hand until you feel resistance, then pull hard enough that you hear a “pop” as you compress the piston inside the engine cylinder. Continue pulling slowly until you can’t pull anymore, then release your grip on both levers and let them snap back into place.
  4. Pull up on the starter rope again until you can’t pull anymore, and release.

How to start a Stihl chainsaw?

Starting a Stihl chainsaw involves a specific set of steps to ensure the safety of the user and the proper functioning of the tool. Here is a step-by-step guide to starting a Stihl chainsaw:

  • Step 1: Check the chainsaw before starting. Inspect the chainsaw for any signs of damage or wear and tear. Make sure the chain is sharp and tight, and that the fuel and oil levels are sufficient.
  • Step 2: Secure the chainsaw. Place the chainsaw on a flat, level surface, and engage the chain brake by pushing the front hand guard forward.
  • Step 3: Switch it on. Turn the ignition switch to the ON position. Make sure that the choke control is in the closed position.
  • Step 4: Prime the engine. Press the fuel pump bulb several times until fuel can be seen in the fuel lines. This is typically done until the bulb feels firm.
  • Step 5: Set the choke and throttle lock. Push the choke control down and lock the throttle trigger.
  • Step 6: Pull the starter cord. Grasp the starter cord handle and gently pull until the engine fires. Then, push the choke control up to the open position.
  • Step 7: Warm up the engine. Let the engine run on idle for a few seconds to warm it up.
  • Step 8: Disengage the chain brake. Push the front hand guard back towards the top handle to disengage the chain brake.
  • Step 9: Begin cutting. Place the chainsaw against the wood to be cut and gently apply pressure to the throttle trigger to start the chain moving. Begin cutting using an overhand grip on the top handle.

Starting a Stihl chainsaw is similar to starting other small gasoline engines. Here are some tips to keep in mind when using a Stihl chainsaw:

  • Maintain proper balance and footing while using a chainsaw. Never operate a chainsaw while on a ladder or unstable surface.
  • Always wear appropriate safety gear, including a hardhat, eye protection, hearing protection, gloves, and boots with steel toes.
  • Use the appropriate size and style of chainsaw for the job at hand.
  • Follow the manufacturer’s guidelines for fuel mixture, and always use fresh fuel to prevent engine damage.
  • Take frequent breaks while operating a chainsaw to avoid fatigue and reduce the risk of accidents.
  • Always keep the chain sharp and properly tensioned to prevent it from jumping or bouncing during use.
  • Never force a chainsaw through wood that is too large or tough. This can cause damage to the chainsaw and pose a safety risk.
  • Always turn off the chainsaw and engage the chain brake when not in use.

By following these steps and tips, you can safely and effectively operate a Stihl chainsaw for all your cutting needs.

Stihl MS 180 C-BE Repair Manual

The Stihl MS 180 C-BE chain saw is a small-to-medium-sized saw designed for cutting firewood and felling trees.

First, it is important to note that it is always best to leave more complicated and major repairs to qualified professionals or authorized service centers. Attempting to repair complex issues yourself may end up causing more harm than good.

That said, there are some simple repairs and maintenance routines that you can do to keep your Stihl chainsaw running smoothly.

1. Regular cleaning

Keeping your chainsaw clean is crucial to its performance and durability. You should clean it after every use, especially if you have been using it in dusty conditions. Use a soft brush to remove debris and dirt from the body of the chainsaw and a compressed air can to blow away the dust from the air filter.

2. Oil and fuel change

Stihl MS 180 C-BE comes with a two-stroke engine, which requires a mixture of oil and gasoline. You have to use the proper mixture recommended by the manufacturer (typically 50:1).

3. Chain and bar maintenance

The chainsaw’s chain and bar wear out over time, which can diminish their cutting efficiency or even cause kickback. Regular maintenance includes sharpening the chain, checking the bar for any nicks or damage, and adjusting the chain tension to ensure it is firmly in place.

4. Spark plug replacement

The spark plug ignites the gas mixture in the engine, and a faulty plug can lead to poor engine performance and starting issues. Replace the spark plug regularly or if you notice any signs of wear or damage.

Check Here You Can Read Buyer Reviews, Know More About MS 180 C-BE Chainsaw

Tips for using the Stihl MS 180 C-BE chainsaw

The Stihl MS 180 C-BE chainsaw is a compact, lightweight saw that is great for cutting firewood and felling small trees. It features the Stihl Quickstop inertia chain brake, which helps prevent accidents by stopping the chain in fractions of a second if it comes in contact with an object when the throttle trigger is released.

You must also learn how to use it properly and safely. You should never operate a chain saw without reading its owner’s manual first. With that in mind, here are some other tips for using your chain saw.

  1. Make sure the chain brake has been engaged before starting the engine. The chain brake should be disengaged before cutting anything.
  2. Never start the chain saw with your hand on the throttle! This can cause the chain to kick back, resulting in serious injury.
  3. Removing the oil tank cap while the engine is running can result in hot oil spraying you in the face and eyes.
  4. The same thing may happen if you remove a fuel cap while it’s running. So turn off your engine before removing either of these caps.
  5. Wear proper safety gear when operating a chain saw, including leather chaps or pants, eye protection, a hard hat, steel-toed boots, gloves, etc., as well as hearing protection and safety glasses (that are vented so you can hear what’s going on).
  6. Wear bright colors, so others can see you.

Stihl MS 180 C-BE Troubleshooting

Despite the powerful engine and performance, you may occasionally encounter issues with your Stihl MS 180 C-BE chainsaw while in use. If any problems do crop up, consult this helpful troubleshooting guide to resolve the issue quickly and get back to work.

Engine won’t start
Possible causes:
1) Fuel tank is empty
2) Fuel filter is clogged and needs to be replaced
3) Ignition system is broken
4) Throttle link is out of adjustment
5) Spark plug wire is loose or disconnected
6) Air filter is dirty, clogged, or needs to be replaced

Engine Lacks Power
Did you add the recommended fuel/oil mixture? Add recommended mix (50:1 ratio).
Did you check for damage or malfunction in the spark plug? Replace or repair spark plug as needed.
Is there sufficient air flow through the air filter cover? Clean filter cover or replace filter if necessary.

Chain Does Not Advance Around Guide Bar​
A common cause of this is lack of chain oil. Check the oil level and adjust as necessary.
If the chain does not advance around the guide bar, this can damage the bar and/or chain.
The saw should be turned off immediately, the bar and chain removed, and all parts checked for proper assembly before using again.


The Stihl MS 180 C-BE is a great all-around chainsaw, and it’s small enough to use for trimming, while still giving you the power to cut firewood. It comes ready to go out of the box, with one exception: you’ll need to buy some bar oil before you can use it.