Stihl ms 291 hard to pull start? Have you been struggling to get your Stihl ms 291 started for some time now? If so, it sounds like you’re not alone. This article will give you the necessary advice and guidance on how to fix the problem so that your ms 291 starts up on the first day.

Why is the Stihl ms 291 hard to pull start?

stihl ms 291 hard to pull start

Here are the most common causes of a hard-to-pull start on a Stihl ms 291:

  • Broken or corroded cables. If the cables on your Stihl ms 291 are broken or corroded, this can cause the machine to be difficult to start. In order to fix this, you will need to replace the cables.
  • Faulty electric motor. If the electric motor on your Stihl ms 291 is faulty, this can also cause the machine to be difficult to start. In order to fix this, you will need to replace the electric motor.
  • Damaged gears or transmission. If the gears or transmission on your Stihl ms 291 are damaged, this can also cause the machine to be difficult to start. In order to fix this, you will need to replace the gears or transmission.
  • Defective fuel pump. If the fuel pump on your Stihl ms 291 is defective, this can also cause the machine to be difficult to start. In order to fix this, you will need to replace the fuel pump.

How to fix Stihl ms 291 hard to pull?

If your Stihl ms 291 is hard to pull start, there are a few things that you can do to fix the problem. Here are the steps that you need to follow:

  1. Check the fuel level. Make sure that the fuel level is correct. If it is low, try adding more oil to the carburetor.
  2. Check the compression. Check the compression of the engine by pressing down on the piston with your hand. If it is low, you may need to replace the piston or cylinder.
  3. Check the spark plugs and wires. Replace any spark plugs and wires that are worn out. Also, check for any loose connections at the spark plug terminals.
  4. Clean and adjust the air filter. Clean and adjust the air filter if it is dirty. Make sure that it is properly seated in the air intake system.

How do I make ms 291 chainsaw start easier?

If you’re having trouble starting your Stihl ms 291 chainsaw, there are a few things you can do to make it easier. The first thing you can do is check the oil level. Make sure that the oil is at the correct level and that it’s been properly filled. If the chainsaw isn’t getting oil from the reservoir, you may need to replace the filter or add more oil.

Another common problem is bad gas mileage. The ms 291 chainsaw requires high-quality gas to start correctly, so if your fuel is of poor quality, it may not ignite correctly and cause problems when trying to start the chainsaw.

If neither of these solutions work, try cleaning out the carburetor and replacing all of the jets with new ones. This will improve the fuel flow and should help to start the chainsaw more easily.

Other Common Problems with Stihl ms291

If you’re having trouble starting your Stihl ms291 chainsaw, there may be a few things you can do to fix the problem. Here are some common problems and how to fix them:

  • Fuel is low: Make sure that the fuel tank is full before trying to start the saw. If the tank is empty, you may need to add fuel.
  • Air is blocked: Check to see if there is any obstruction in the air flow around the spark plug area. This can be caused by dirt, leaves, or other debris. Clean out the area if necessary.
  • Chain is dirty or fouled: Check the chain for dirt, rust, or other debris. Clean it if necessary. Also, make sure that the chain tensioner is properly adjusted – too much slack in the chain will cause it to bind and stop turning.

Stihl 291 chainsaw pull cord locked up

The bar could be caught on something when you were trying to start the chainsaw. The chain may have gotten caught on the bar during operation. The clutch might be worn out and not release the chain from the bar properly. Check to see if anything is caught on the bar when you try to start it.

If there is nothing caught on the bar, make sure that you are putting enough force into your pull. Check the chain and/or sprocket for wear or damage. If either of these items is damaged or worn out, it will affect how easily the chain can slide off of the sprocket. Replace them as necessary. Swap out the clutch if it seems to be causing problems with starting the chainsaw. Clutches can wear out over time, and a new clutch will often fix this problem.

Stihl 291 chainsaw too much compression

Check the compression of the engine. If the chainsaw is too much compression, it may be difficult to start. You can check the compression by pulling the spark plug out and holding it in your hand.

The plug should be tight against your thumb. If the chainsaw is too little compression, it may start easily but will not run smoothly. Make sure there is oil in the engine. If there isn’t enough oil in the engine, it may be hard to start. You can check the oil level by looking through the side window and seeing how high the oil level is on top of the engine.

Make sure to add enough oil so that it covers the entire bottom of the engine. Check for foreign objects in the engine. If there are any foreign objects in the engine, they may block the spark plug or other parts of the engine from working properly. Remove any foreign objects that you find and try starting your chainsaw again.

To use the gauge, unscrew the cap on the end of the bar and place it over the sprocket. The higher the number, the higher the compression. To measure the stroke, place a stopwatch next to the engine and start it up.

As you pull the trigger, note how long it takes for the chain to reach full extension. This will give you an idea of how much compression is present in the engine. If either of these methods shows that there is too much compression, there are a few things that you can do to fix it: 1. Change out the spark plug: If there is too much resistance when trying to start your Stihl 291 chainsaw, chances are that one or more of your spark.

Stihl ms291 chainsaw pull cord stuck

Make sure the chain is properly engaged on the sprocket. You can do this by checking the chain tension with a feeler gauge or by using a chain checker. The chain should have at least 6-7 links to slack. Check the pull cord for kinks or twists. If there are any kinks or twists, use a wire brush to remove them. Make sure the pull cord is properly installed on the starter motor.

If it isn’t, adjust it so that it is snug but not tight. Make sure all of the electrical connectors are properly connected.5. Check that the oil level is correct and that the chain is lubricated well enough to function properly.

Stihl ms 291 chainsaw pull cord won’t pull

If your Stihl ms 291 chainsaw pull cord won’t pull, there are a few things you can do to fix it. Check the chain tension. Make sure the chain is tight against the bar and that the bar is tight against the sprocket. You can check chain tension by using a gauge or by pulling on the cord itself. Check for binding. If the cord is binding at any point, it may not be able to pull properly.

Try to remove any debris or grit that may be preventing the cord from moving freely. Check for kinks or twists in the cord. If there are any kinks or twists in the cord, they may cause it to bind and not pull properly. Try to straighten out any kinks or twists with a heating iron or by using a wire brush.

Check for loose parts. If you notice any loose parts on the chainsaw, they may cause the cord to bind and not pull properly. Tighten all of the screws that hold the chainsaw together, and replace any worn parts as needed.

Conclusion

If you’re having trouble starting your Stihl ms 291 chainsaw, here’s a quick guide on how to fix it. Sometimes the problem can be as simple as trying to pull the starter rope too tight or making sure that the clutch is properly engaged. If you still can’t get your saw started after following these steps, please feel free to give us a call at our shop and one of our experts will be happy to help diagnose and fix your chainsaw.